Outdoor & Pressure Washing Sydney
Remove built-up grime, algae, dirt, and outdoor contamination from suitable tiled and hard surface areas, cleaned with the pressure and method your surface actually calls for.
- Ceramic Tile
- Natural Stone
- Concrete
- Pavers
Between coastal humidity, seasonal rain and long dry spells, Sydney’s climate gives algae and moss exactly what they need to take hold on shaded patios, pool surrounds and south-facing paving. Add falling leaves, garden run-off, everyday foot traffic and airborne dust, and most outdoor tiled or hard surfaces are carrying a mix of organic and general contamination within a year of being installed even when they’re swept and rinsed regularly.
The surface underneath that grime matters just as much as the grime itself. A honed sandstone pool surround, a glazed porcelain patio and an exposed aggregate driveway all respond differently to water pressure, heat and cleaning agents. That’s the part a generic pressure washing visit tends to skip and the part we start with.
Outdoor Areas We Clean
Any hard, fixed outdoor surface around your home or property is assessed first and cleaned second.
- Ceramic / Stone
- Stone / Porcelain
- Ceramic / Stone
- Pavers
- Concrete / Pavers
- Concrete / Stone
- Ceramic / Stone
- Ceramic / Stone
- Mixed Surfaces
Built-Up Outdoor Contamination
Algae
Moss
Surface Dirt
Built-Up Grime
Organic Deposits
General Outdoor Contamination
Results depend on the surface, the age of the contamination and how it was sealed or maintained. We’ll always tell you honestly what to expect during your inspection, rather than promise a result before we’ve seen the surface.
How We Work
Our Outdoor Cleaning Process
The same sequence, every time , because the order protects the surface.
Inspect Surface
We walk the area and check the condition, wear, sealant and existing damage before anything is switched on.
Identify Material
Ceramic, porcelain, natural stone, concrete, or pavers—the material determines everything that follows.
Prepare Area
Furniture, plants and drainage points are protected, and loose debris is cleared first.
Apply Suitable Cleaning Treatment
Where needed, a treatment suited to the material and the contamination is applied to loosen build-up before pressure is used.
Controlled Pressure Cleaning
Pressure, nozzle, and technique are set for that specific surface and not run at a single default setting across the job.
Final Rinse & Inspection
The area is rinsed clear and checked with you, so you can see the result before we finish up.
Pressure Washing Isn't One Size Fits All
Most pressure washing companies run one setting on every job. We treat the surface first and the dirt second because the wrong pressure on the right surface still causes damage.
Surface
Common Risk
Approach
Notes
Natural Stone
Pitting, surface etching
Lower pressure, stone-safe method
Sandstone, travertine and limestone are softer than they look and need care.
Concrete
Surface pitting on worn slabs
Higher pressure where the slab allows it
Sealed or freshly finished concrete is treated more gently.
Pavers
Joint sand loss, edge lifting
Angled pressure, joint-aware technique
We avoid blasting straight down into joints wherever possible.
Ceramic Tile
Glaze scratching, grout erosion
Moderate pressure, wide fan tip
Grout lines are checked before cleaning; worn grout takes less pressure well.
Before & After
Outcomes depend on the stone type, how deep any scratching or etching goes, and its overall condition; restoration refines and revives stone, it doesn’t reinvent it.
- Homes
- Apartments
- Strata Properties
- Restaurants
- Hotels
- Commercial Properties
Frequently Asked Questions
Can you pressure clean outdoor tiles?
Yes. Outdoor ceramic and porcelain tiles are one of the surfaces we work with most often. We check the glaze, grout condition and wear before setting our pressure and nozzle choice.
Can pressure washing damage tiles?
It can, if the pressure, distance or technique isn’t matched to the tile and grout. That’s why identifying the material is a fixed step in our process, not an optional extra.
Can you clean pool surrounds?
Yes. Pool surrounds are usually shaded, damp and prone to algae, so they get particular attention on stone and porcelain surrounds.
Can you remove algae?
In most cases, yes. Surface algae responds well to the right treatment and controlled pressure. Deep or long-term staining underneath the algae isn’t always fully removable, and we’ll be upfront about that during inspection.
Do you clean patios?
Yes, patios are one of our core outdoor areas, including tiled, stone and paved patios and surrounding entertaining spaces.
Can natural stone be pressure cleaned?
Yes, but at lower pressure and with a stone-appropriate method. Sandstone, travertine and limestone are softer than concrete or ceramic and are treated accordingly.
How much does outdoor pressure washing cost?
Cost depends on the surface material, the size of the area and the level of build-up present. We provide a free, obligation-free quote after a quick look at the area or photos.
Make Your Outdoor Areas Look Ready To Use Again
Tell us about your patio, pool surround, driveway or paving and we’ll recommend the right approach free of charge.